Driving brings much convenience to the user, and also the selection and purchase of a car, we need to also refer to the machine and keep it in good condition in order to continue the good service for at least the next 50-10 years .
Today I spent with you the DIY Basic Guide to car-sharing service and how you can make yourself and also save time and cost of auto mechanic!
Basic Guide to DIY Auto Maintenance
The first thing to dois to look under the hood. It looks like a maze, is not it? In essence, the underlying system is the fuel, ignition and cooling system.
We are not going into details, as a system of all these works. Instead, we try to understand how can the simple weekly checks on the car, and what are seen to respect the property, to do so.
DIY car maintenance – to ensure the objects is
1) Fluids
– Engine oil liquid
– Refrigerant
– WindshieldLiquids
– Laundry Liquids
– Brake fluid
– Power steering fluid
2) the tire pressure
DIY car maintenance (1st) – Engine Oil Fluids
TIP: Always check with oil when the engine was shut down to avoid a long period of hot oil burns shot himself.
Purpose of liquid motor oil:
To prevent smudging of the car and engine wear.
Steps to follow:
First clean the engine oil dipstick is provided byManufacturer
According Insert the shaft into the engine, then lift and check the level. If the top edge of the oil is above the ADD mark, the oil level is acceptable, otherwise it must immediately add the oil. Normally, the amount needed is a liter of oil.
Third To add oil, open the engine oil cap, place a funnel over the opening, and slowly pour the oil in it.
Fourth wait a few minutes and then check the oil level once again to ensure that oil level is now "Add" and "brand" FULL.Make sure no oil over the mark, because they reduce the quality of the lubricating oil and less effective to add.
DIY car maintenance (1b) – refrigerants
The purpose of refrigerants:
Circulating a car engine to remove excess heat. A mixture of water and antifreeze, which stores the heat ee take the radiator, where the airflow cools the liquid before returning back to cool the engine.
Steps to follow:
1) Make sure thatEngine and radiator have cooled down before checking the coolant level.
2:00) Locate the radiator and coolant reservoir corresponding reserve, the participation of the top layer of the coolant from the radiator. Check and make sure the coolant level is at minimum and maximum levels.
3) If the need for top-up arises, turn the radiator cap counter-clockwise to turn the first quarter, all the pressure that remains in the cooling system built before all manner of open space the cap.
4)Add coolant as necessary to level within the MIN and MAX.
5) Replace cap and make a fundamental reorganization.
DIY car maintenance (1c) – windshield fluid
The purpose of windshield fluid:
To clean the windshield, if necessary.
Steps to follow:
1) Locate the washer fluid reservoir. It looks like a white plastic milk jug or glass, and keep a small amount of windshield fluid.
2) In most cases, you can create a visual inspection of the liquid,and until one or two inches below the top, as it is full, and do not require topping up.
3) If it is too low, simply unscrew the cap and business plan with half a glass of water washing, or make your own DIY windshield fluid, by adding a few drops of detergent in water.
4) back and do a complete renovation.
DIY car maintenance (1d) – brake fluid
The purpose of the brake fluid:
Support systems that activate the hydraulic brakeSystems function properly.
Steps to follow:
1) Find the brake master cylinder
2) Clean the top of the tank before removing the cover with a key
3) Check and ensure that the brake fluid up to the mark "FULL. Do not compromise, because this is a crucial factor in vehicle safety.
4) Top closely with the brake fluid through a funnel until the level is about an inch below the tip.
Note:
brake fluid have different quality, soYou should check the manuals for your specific needs.
Do not touch the brake fluid to paint, you're in a nasty surprise.
5) Replace and tighten the cap, if you did.
DIY car maintenance (1e) – Power Steering Fluid
The purpose of the Fluid Power Steering:
Required for vehicles with power steering capability turned on, without which it is very difficult to turn the steering wheel.
Steps to follow:
1) Find the power steeringTank
2) Remove the lid and check the current level.
Tip: Make the check box only if the engine has cooled, otherwise the readings will be inaccurate, because the hot liquid expands when.
3) Top-up the power steering fluid that the vehicle specified in the manuals, and be careful not to overfill it.
4) Replace and tighten the cap, if you did.
DIY CAR CARE (2) – tire pressure monitoring auto
The aim of the tire pressure check:
MagazinesControls will help maximize the life of the tires because the pressure is not correct lead to lower contact with the streets of life caused by contact with the road safety problems. Under-inflated tires also reduce fuel consumption without knowing it, at higher costs.
Steps to follow:
1) Check out the tire pressure recommended by car manuals, measured in psi required.
2) To facilitate the control to go to any gas station, and set their tire pressure gaugein your car tire valve stem. Push until you feel a breeze, and then release it. Notice the ad directly on the machine gauge tire pressure.
3) When the pressure is not enough, add to the line of air-air, and whether the pressure is made. If the air pressure is too high to allow a little 'air measured with the tires and check before releasing more air.
4) Replace the valve cap when done.
5) Repeat for all tires.
SUGGESTION: 'well, a quick searchCheck the tires and replace every morning for a better vehicle for safety.
Completion
In summary, to ensure a better understanding of the key points is to follow your car during routine maintenance, and measures during maintenance, it is now able to park your car in tiptop maintain power continuously, and maximizing the joy in car trips for you and your family.
audiobook debtconlidation